Gravity Water Filter System Removes Fluoride!Removes bacteria and the harmful crap from your water! Description:(1) 1.75-gallon food-grade, BPA-free plastic bucket(1) 4″x4″ low-profile silver-impregnated ceramic filter with activated charcoal and anti-fluoride core (-) NOT WITH THIS AUCTION – Primo ceramic water dispenser with spigot(-) NOT WITH THIS AUCTION – cool wooden stand That’s it! It’s the simplest thing in the world! But it works, and gives you good-tasting water! A friend said he got a stainless steel Berkey that does the same thing – but with this, we got the same pure water to drink at a fraction of his cost! (And, if you have a large bottle of bottled water you want to use for company, just take the filter container off, and put the bottle on top of the crock – it works as a water dispenser, too!) These filters are produced here in the US, and are just as good – if not better – than the Sterasyl filters we used to use when we lived overseas. They are rated at 0.2 micron pore size, so they will filter 99.99% of particles larger than 0.2 microns in size. They are silver impregnated, so they actually KILL bacteria and amoeba that try to swim through the filter with the water! There is a core of activated charcoal that removes bad tastes and odors from the water, and a special matrix of anti-fluoride resin. To use this on a regular basis, you’ll have to clean the filter when the water that SHOULD flow through turns into a dribble. Some people use a green kitchen pot cleaner – if you do, make sure it’s an OLD one that’s been worn down, so you don’t wear down your filter too much. Anti-Fluoride filters like these should last 6 months, being used on a daily basis. Shipping note: 1 box with the plastic filter container for the top, along with the ceramic filter(s). Installation:It’s very easy to install the filter in the container. Take your filter out of the box, and you’ll see a wingnut and 2 silicon washers on the bottom. Unscrew the wingnut, and set it aside. Take one of the silicon washers off. Put the threaded shaft on the bottom of the filter through the small hole in the bottom of the container, so the shaft comes out the bottom of the container. The filter stays in the filter container. Put the silicon washer back on the threaded shaft, and then screw the wingnut back onto the shaft. When you tighten the wingnut, please hold onto the plastic base of the filter – DO NOT hold the filter, itself. If you hold the filter and you twist it off its base, you will have to purchase another filter. Turn the wingnut so it is tight. That’s it! Now set the filter container on top of the crock, and pour about 1 1/2 gallons of tap water into the container. The first time you use the filter, it’ll seem like it takes forever for the water to work its way through the ceramic. After they get saturated, it won’t take as long for the water to run through it, but please don’t expect to get a ton of water flow-through with a bucket this size. Also, please expect tons of little black thingies in the water the first few times you use the filter. That’s normal. It’s just some of the finely powdered activated charcoal slipping through the mesh lining in the core of the filter. Some people throw that water away, and put fresh water in the top bucket. I just drink the stuff. I used to pay good money for pills of activated charcoal for stomach problems, and finally realized that I could get that same charcoal for free if I would just ignore the dark specks and drink the water! Water flow-through depends on the «head» of water that’s above the filters. If you need a lot of water, get one of the uglier 5-gallon or 6-gallon plastic bucket systems that I’ve got listed. This will provide you with tasty water to drink, but you’ll have to be diligent about refilling the top bucket every time you fill up a glass from the full crock below. It’s a tortoise – not a rabbit. Replacement filters are available. They cost $35 each, or 2 for $66.50, plus shipping.I currently have a listing for the replacement filters – click on the «See Other Items» in the upper right hand corner of this page. I will include contact information along with the top filter assembly, so you can contact me directly with any questions, if you so desire. Rinse with clean water, and refill with any old pond or river water again.NEVER use soap on the filters. Soap will RUIN them. Technical Info: These filters will remove…99% Arsenic 599% Hydrogen Sulfide (Rotten egg odor – H2S)95% Chlorine and Chloramines99% bad taste99% bad odors98% Aluminum96% Iron98% Lead90% Pesticides85% Insecticides90% Rat poisons85% Phenols85% MTBE85% Perchlorate80% Trihalomethanes 95% Polyaromatic hydrocarbons100% Giardia Lamblia100% Cyclospora100% live Cryptosporidium (WRc Standard)100% Cryptosporidium (NSF standard 53)100% E. Coli, Vibrio Cholarae99.999% Salmonella Typhil, Shigella Dysenteria99.999% bacteria and Fluoride. Note: Because of the wide variations between municipalities and how much fluoride they put into their water systems, it’s impossible to generically determine the percentage that’s removed.At first, almost all of the tested municipalities’ fluoride will be removed. Then after 3-4 months, the efficacy goes down. These AFl filters need to be replaced approx. every 6 months to keep your fluoride levels down to the desired levels. The silver component of the filter will still be good – just dry the filter out after you replace it, and store it for later use when you are trying to filter the other impurities. Each filter should be good for a total of at least 1 year – depending, of course, how often it gets dirty and you have to clean it. Each cleaning removes the top layer of the ceramic shell…. Dry Storage Life: indefinite.Wet Usage Life: about 1 year for the silver ceramic shell, 6 months for the anti-fluoride element
anti-fluoride ceramic + silver filter and Primo water crock
Gravity Water Filter SystemRemoves Fluoride!Removes bacteria and the harmful crap from your water! Description:(1) 1.75-gallon food-grade, BPA-free plastic bucket(1) 4″x4″ low-profile silver-impregnated ceramic filter with activated charcoal and anti-fluoride core(1) Primo ceramic water dispenser with spigot(1) cool wooden stand That’s it! It’s the simplest thing in the world! But it works, and gives you good-tasting water! A friend said he got a stainless steel Berkey that does the same thing – but with this, we got the same pure water to drink at a fraction of his cost! (And, if you have a large bottle of bottled water you want to use for company, just take the filter container off, and put the bottle on top of the crock – it works as a water dispenser, too!) These filters are produced here in the US, and are just as good – if not better – than the British Sterasyl filters we used to use when we lived overseas. They are rated at 0.2 micron pore size, so they will filter 99.99% of particles larger than 0.2 microns in size. They are silver impregnated, so they actually KILL bacteria and amoeba that try to swim through the filter with the water! There is a core of activated charcoal that removes bad tastes and odors from the water, and a special matrix of anti-fluoride resin. To use this on a regular basis, you’ll have to clean the filter when the water that SHOULD flow through turns into a dribble. Some people use a green kitchen pot cleaner – if you do, make sure it’s an OLD one that’s been worn down, so you don’t wear down your filter too much. Anti-Fluoride filters like these should last 6 months, if they are used on a steady, daily basis. Shipping:Please note: This will come in 2 shipments: 1 box with the ceramic crock and wooden legs, and 1 box with the plastic filter container for the top, along with the ceramic filters. Note further – these must be shipped by either UPS or FedEx to keep the shipping charges low. If you cannot have it shipped to a street address, please don’t buy one.Installation:First, decide whether you want to use the wooden legs to support the crock, or not. If you want the legs, you’ll have to get a Phillips screwdriver and put it together. The big screw goes in the middle hole – the 4 smaller ones go around the edges. It’s very easy to install the filter in the container. Take your filter out of the box, and you’ll see a wingnut and 2 silicon washers on the bottom. Unscrew the wingnut, and set it aside. Take one of the silicon washers off. Put the threaded shaft on the bottom of the filter through one of the small holes in the bottom of the container, so the shaft comes out the bottom of the container. The filter stays in the filter container. Put the silicon washer back on the threaded shaft, and then screw the wingnut back onto the shaft. When you tighten the wingnut, please hold onto the plastic base of the filter – DO NOT hold the filter, itself. If you hold the filter and you twist it off its base, you will have to purchase another filter. Turn the wingnut so it is tight. That’s it! Now set the filter container on top of the crock, and pour about 1 1/2 gallons of tap water into the container. The first time you use the filter, it’ll seem like it takes forever for the water to work its way through the ceramic. After they get saturated, it won’t take as long for the water to run through it, but please don’t expect to get a ton of water flow-through with a bucket this size. Also, please expect tons of little black thingies in the water the first few times you use the filter. That’s normal. It’s just some of the finely powdered activated charcoal slipping through the mesh lining in the core of the filter. Some people throw that water away, and put fresh water in the top bucket. I just drink the stuff. I used to pay good money for pills of activated charcoal for stomach problems, and finally realized that I could get that same charcoal for free if I would just ignore the dark specks and drink the water! Water flow-through depends on the «head» of water that’s above the filters. If you need a lot of water, get one of the uglier 5-gallon or 6-gallon plastic bucket systems that I’ve got listed. This will provide you with tasty water to drink, but you’ll have to be diligent about refilling the top bucket every time you fill up a glass from the full crock below. It’s a tortoise – not a rabbit. Replacement filters are available. They cost $45 each plus shipping.I currently have a listing for the replacement filters – click on the «See Other Items» in the upper right hand corner of this page. I will include contact information along with the top filter assembly, so you can contact me directly with any questions, if you so desire. Rinse with clean water, and refill with any old pond or river water again.NEVER use soap on the filters. Soap will RUIN them. You can speed up the filtering by making a siphon hose:Get a piece of 5/16″ OD clear plastic hose, and push it up over the threads on the bottom of the filter. Let it hang down in the crock so the end rests on the bottom of the crock. When clear water flows and covers the end of the hose, it will start siphoning water through the filter, and will speed up the filtering process. Technical Info: These filters will remove…99% Arsenic 599% Hydrogen Sulfide (Rotten egg odor – H2S)95% Chlorine and Chloramines99% bad taste99% bad odors98% Aluminum96% Iron98% Lead90% Pesticides85% Insecticides90% Rat poisons85% Phenols85% MTBE85% Perchlorate80% Trihalomethanes 95% Polyaromatic hydrocarbons100% Giardia Lamblia100% Cyclospora100% live Cryptosporidium (WRc Standard)100% Cryptosporidium (NSF standard 53)100% E. Coli, Vibrio Cholarae99.999% Salmonella Typhil, Shigella Dysenteria99.999% bacteriaand Fluoride. Note: Because of the wide variations between municipalities and how much fluoride they put into their water systems, it’s impossible to generically determine the percentage that’s removed.At first, almost all of the tested municipalities’ fluoride will be removed. Then after 3-4 months, the efficacy goes down. These AFl filters need to be replaced approx. every 6 months to keep your fluoride levels down to the desired levels. The silver component of the filter will still be good – just dry the filter out after you replace it, and store it for later use when you are trying to filter the other impurities. Each filter should be good for a total of at least 1 year – depending, of course, how often it gets dirty and you have to clean it. Each cleaning removes the top layer of the ceramic shell…. Dry Storage Life: indefinite.Wet Usage Life: about 1 year for the silver ceramic shell, 6 months for the anti-fluoride element, if used on a continuous basis
14 oz Silver Cooks Companion Hydro Bottle H2 Generator New
Hydrogen water generator. Has many health benefits. Quality of Life during Radiation Therapy: One study indicated that drinking hydrogen-rich water during radiation therapy for liver cancer improved the quality of life for participants.
Enagic Leveluk SD501 Platinum Alkaline Ionizer Water Filter Silver
Enagic Leveluk SD501 Platinum Alkaline Ionizer Water Filter in Silver High-quality water purification device that utilizes an alkaline ionization process to remove chlorine taste and odor from your tap water. Very Good Working Condition *Will need a new filter
ZeroWater 5-stage water filter replacement – 4 pack
Plus, you can help stop plastic waste and save up to 110 single-use plastic bottles per filter. 15 Gallon estimated water filter life: Filter life can vary depending on your water quality. Eco-friendly: Save up to 110 single-use plastic bottles per filter or up to 660 bottles a year while enjoying cleaner, healthier water.
10″ Clear Standard Whole House Water Filter System 25 Micron Sediment Filter
Untitled Document 10 Inches Transparent Standard Whole House Water Filter System with Presser Relief Valve, 3/4” Inlet/Outlet Brass Port and Sediment Cartridge 25 Micron Product Description DURABLE STRUCTURE: 10” Transparent Standard Housing is proper for heavy sediment applications. The housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. 10” Standard 25 Micron Sediment Filters Used for effectively removing most sediments from water POINT OF USE: This System for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, well water filtration, food service, and irrigation. Extends life of Washing Machines, Water Heaters & Other Household Appliances. Keeps water fresh by reducing sediment, scale, rust, dirt, sands, and silt EASY TO OPERATE: There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief button on the inlet side of the cap releases pressure in the housing for changing filter cartridges. Unique cap design allow quickly and easy to remove housing to replace cartridges. Transparent housing body allows visually to determine when cartridge should be changed 25 MICRON SEDIMENT CARTRIDGE is wrapped and sealed and meets NSF Standards and Regulations. Dimensions: 10” x 2.5”. WELL-MATCHED: Dupont PFC5002, WFPFC5002, 3M CFS110, AP110-NP, AP101S, AP101T, Aqua Pure AP110, AP11T, AP51T, Hydronix SGC-25-1005, Culligan P5, P5-D, P5A, OmniFilter RS14-SD and RS14-SS, GE FXUSC, Aquaboon S-5M, Manitowoc K-00173, Whirlpool WHKF-GD05, American Plumber W5P, Pureplus PP10-05, however for best preferment use only original RONAQUA CARTRIDGES WELL-MATCHED FOLLOWING HOUSINGS SYSTEMS: DuPont WFPF38001C, WFPF13003B, Culligan WTR Filter HF-360A and HF-150A, American Plumber WC34-PR, Geekpure RO5-FH10, Hydronix HF3-10CLBK34, EcoPure EPW2 Description: The 10″ Transparent Standard Housing for Whole House Water Filtration System with 3/4″ Inlet / Outlet Brass Ports (RA-125-10) is proper to use for reducing sediment, dirt, rust, & suspended particles in incoming water to you house. The transparent housing body is made of reinforced polypropylene for strength and resistance to chemicals, and the blue cap is made of high-flow polypropylene for toughness. The blue cap has 3/4″ inlet / outlet brass ports which allowed better sealed connections to the corresponding pipes. There is rubber O-ring on the top of the housing body to ensure a watertight seal. A pressure relief valve on the outlet side of the cap releases pressure in the housing for changing filter cartridges. Those Housings for use in various applications and is usually placed in the main water line entering the house including, but not limited to residential drinking water filtration, food service, and irrigation. Easy to connect multiply housings in one Custom Whole House Water Filtration System to fit your specific needs. Filter Cartridges Included in this Set are Melt-blown Four Layers Filtration Polypropylene Sediment Filter A Sediment Water Filter removes the physical debris and impurities from your water. The sediment filter has tiny holes through which water is able to pass, however the unwanted particles are not. As these particles come in different sizes, so do the filters. The filter sizes are measured in microns, the smaller the micron measurement, the smaller the holes in the filter, allowing to hold back the smallest of particles. Generally, for water that is more visibly polluted, containing larger particles, a sediment filter of a larger size (such as 20 or 50 microns) is recommended in the first stage of installation to prevent the clogging of the next stage(s) of filters. This sediment filter is often the first filter installed in the Reverse Osmosis circuit and acts as a net as it catches unwanted particles, including sand, dirt, silt, rust, and other fine particles. Sediment filters are made of fine melted polypropylene, which is then blown and spun into a cylinder-like form. Polypropylene is a substance that is resistant to chemical solvents, bases, and acids. Removal of these particles allows filters, such as Carbon Block or GAC (Granular Activated Carbon) filters, to perform better and for longer periods of time. These particles and pollutants come from water sources, old and dirty pipes, as well as contaminants that are used to treat the water. Multi-layer Gradient Filtration Outer Zone Mid Zone Inner Zone Innermost Zone These Sediment Water Filters Intercept all Following Impurities Rust & Corrosion- Rust is a type of corrosion. Corrosion is the process by which certain materials, metals and non-metals, deteriorate as a result of oxidation. Rusting is oxidation of iron in the presence of air and moisture. … Corrosion requires surface exposure to air or chemicals Coarse Sand is our concrete sand that is washed and screened to a larger grit than our Fine Washed Sand (masonry sand). Coarse Sand is used with aggregate, water, and cement in the production of ready-mix concrete. Hard Scale causes a variety of problems in the home. Stains are probably the most noticeable result of hard water scale. Stains appear in toilets, sinks, and showers. Some hardwater scale are less noticeable, such as scale build up in pipes and in appliances which can cause costly repairs or the need to replace appliances. Fine Sand is very fine, screened sand that is typically tan in color. This type of sand is commonly used as base sand for above ground swimming pools, paving stones, sidewalk blocks and retaining walls. It is alternately used in stucco and cement applications. Particles is a small localized object to which can be ascribed several physical or chemical properties, such as volume, density, or mass. They vary greatly in size or quantity, from subatomic particles like the electron, to microscopic particles like atoms and molecules, to macroscopic particles like powders and other granular materials. Particles can also be used to create scientific models of even larger objects depending on their density, such as humans moving in a crowd or celestial bodies in motion. Sediment is a naturally occurring material that is broken down by processes of weathering and erosion, and is subsequently transported by the action of wind, water, or ice or by the force of gravity acting on the particles. For example, sand and silt can be carried in suspension in river water and on reaching the sea bed deposited by sedimentation; if buried, they may eventually become sandstone and siltstone (sedimentary rocks) through lithification. Sediments are most often transported by water (fluvial processes), but also wind (aeolian processes) and glaciers. Beach sands and river channel deposits are examples of fluvial transport and deposition, though sediment also often settles out of slow-moving or standing water in lakes and oceans. Desert sand dunes and loess are examples of aeolian transport and deposition. Glacial moraine deposits and till are ice-transported sediments. Dirt is unclean matter, especially when in contact with a person’s clothes, skin or possessions. Common types of dirt include: Dust: a general powder of organic or mineral matter; Filth: foul matter such as excrement; Grime: a black, ingrained dust such as soot; Soil: the mix of clay, sand, and humus which lies on top of bedrock. Silt is granular material of a size between sand and clay, whose mineral origin is quartz & feldspar. Silt may occur as a soil or as sediment mixed in suspension with water and soil in a body of water such as a river. It may also exist as soil deposited at the bottom of a water body, like mudflows from landslides. Silt has a moderate specific area with a typically non-sticky, plastic feel. Silt usually has a floury feel when dry, and a slippery feel when wet. Silt can be visually observed with a hand lens, exhibiting a sparkly appearance. It also can be felt by the tongue as granular when placed on the front teeth (even when mixed with clay particles). Specifications: Filter Type Fine Melted Polypropylene 25 MICRON Flow Rate 5 GPM Unit Height IN/CM 12.5 IN/31.75 CM Operating Temperature 40°F (4.4°C) – 125°F (51.7°C) Unit Length IN/CM 5.125 IN/13.02 CM Operating Pressure 20 PSI (1.4 bar) – 60 PSI (4.5 bar) Unit Width IN/CM 5.125 IN/13.02 CM Cartridge Lifetime Replace two or three times a year – depending on your water quality Inlet/Outlet Ports 3/4″ NPT Bress Cartridge Packaging This filter is wrapped and sealed and meets NSF (National Science Foundation)
LG LT1000P Replacement Refrigerator Refresh Ice Water Filter ADQ747935 US
Part Number: LT1000P. Color: White. Compatible with LFXC24796D, LFXS30796D, LMXC23796D, LMXS30796D, LSFXC2496D. No tools required for installation.
1 PACK Replacement Refrigerator Refresh Water Filter LG LT1000P NSF42 ADQ747935
Description: Compatible with LFXC24796D, LFXS30796D, LMXC23796D, LMXS30796D, LSFXC2496D Horizontal type replacement water filter Filters chlorine taste and odor,Reduces lead, mercury, asbestos and benzene Designed to last up to 6 months or 200 gallons No tools required for installation Specification: Part Number: LT1000P Item Weight: 5.9 ounces Product Dimensions: 2.1 x 2.1 x 7.1 inches Color: White Temperature Range: 38-100 Degrees Fahrenheit External Testing: NSF Compatible with Following Models: GF-D708BSL GF-D708MBSL GF-L570MBL GF-L570PL GF-L677SL GF-L708PL GF-V570MBL GF-V708BSL GF-V708MBSL GF-V910MBSL SG-5I700TSL LFXC24796D LFXC24796S LFXS30796D LFXS30796S LMXC23796D LMXC23796S LMXS30796D LMXS30796S LSFXC2496D LSXC22396D LSXC22396S LSXS26396S Package Include: 1 Pack Sealed Refrigerator Water Filter.
4PACKS Refresh Refrigerator Ice Water Filter For LG LT1000P ADQ747935 Brand New
About the LT1000P / ADQ73693901. By changing your LT1000P / LT1000PC water filter on a regular basis, you’ll continue to reduce contaminates such as iron, particulates. MPN : LG LT1000P. Model : LG LT1000P ADQ747935.
2 Pack LG LT1000P Refresh Refrigerator Ice Water Filter ADQ747935 GF-D706BSL USA
Part Number: LT1000P. 2x Refrigerator Water Filter. Temperature Range: 38-100 Degrees Fahrenheit. Color: White. Compatible with Following Models External Testing: NSF. Designed to last up to 6 months or 200 gallons.
